What is TCP port 1556 used for?
PBX uses the following TCP ports. 1556 : Used to listen for inbound connections from remote hosts via any local network interface. This port number is registered with IANA and should not be used by any non-Veritas applications and should not be changed.
What protocol does NetBackup use?
the TCP protocol
NetBackup primarily uses the TCP protocol to communicate between processes. The processes can run on the same host or on different hosts.
What ports does NetBackup use?
NetBackup client ports
| Source | Destination | Port |
|---|---|---|
| Client | Master server | 13724 * |
| Client | Media server | 1556 |
| Client | Media server | 13724 * * |
| Client | MSDP server | 10102 |
Is port 1556 TCP or UDP?
Port 1556 Details
| Port(s) | Protocol | Service |
|---|---|---|
| 1556 | tcp,udp | veritas |
| 1556 | tcp,udp | ashwin |
| 1556 | tcp | veritas-pbx |
| 1556 | tcp,udp | veritas_pbx |
What is Veritas PBX?
The Veritas Private Branch Exchange (PBX) software is part of the Infrastructure Core Services. This service provides single port access to clients outside the firewall connecting to various services running as part of NetBackup or OpsCenter.
What is Veritas Private Branch Exchange?
How do I check my NetBackup Client Connectivity?
Run the command bptestbpcd -client xxxx (where xxxx is a clientname) to test connection to a client.
What port does PBX use?
PBX Admin Access
| PORT | TCP/UDP | NOTES |
|---|---|---|
| 22 | TCP | Port used to allow SSH to the PBX from the outside world. |
| 80 FreePBX 2001 PBXact | TCP | Used to access the PBX Admin GUI |
| 443 | TCP | Used to access the PBX Admin GUI with SSL encryption |
| 1194 | TCP/UDP | Used to connect OpenVPN clients to PBX VPN Server. |
How do I start Veritas Private Branch Exchange Service?
It can also be used to stop, start, or restart the service.
- Right Click on My Computer and select Manage to open the Computer Management tool.
- Select Services under the Services and Applications section to display a list of services.
- Scroll down the list of services to display Veritas Private Branch Exchange.
How do I start NetBackup in Linux?
To control NetBackup use systemd commands.
- To stop NetBackup and vxpbx: systemctl stop netbackup. service. systemctl stop vxpbx_exchanged. service.
- To start NetBackup and vxpbx: systemctl start vxpbx_exchanged. service.
What is a port 80?
On a Web server or Hypertext Transfer Protocol daemon, port 80 is the port that the server “listens to” or expects to receive from a Web client, assuming that the default was taken when the server was configured or set up.
What is the TCP port 1556 for NetBackup?
Opening TCP port 1556 outbound from NetBackup servers to NetBackup clients will prevent delays that occur while attempting to use PBX. Similarly, opening TCP port 1556 inbound will prevent delays for client-initiated requests to the master server.
What is the port 1556 for Veritas PBX?
Details. Source. 1556. tcp,udp. veritas. Port used by Veritas PBX (Private Branch Exchange) Service. Veritas uses the following ports: 1556 – Veritas PBX Service. 2821 – VxSS Authentication Service.
What is Port 1556 between OpsCenter server and master server?
Open port 1556 (pbx) between the OpsCenter server and master server. OpsCenter Server also uses UDP port 162 outbound for SNMP trap protocol. To backup and restore NDMP filers: Media server (DMA) to NDMP filer (tape or disk) requires TCP port 10000.
What happens when PBX / 1556 is blocked by a firewall?
If the service cannot be reached via the TCP port for PBX/1556 and the TCP port for vnetd/13724 is blocked by a firewall which silently discards the TCP SYN packet, then the operating system connect () API will wait for TCP SYN retry/timeout before failing the connection attempt.