How do I get the code off my Polaris Ranger?
After fixing the underlying cause of your Polaris Ranger error codes and check engine lights, the vehicle should clear the codes automatically. Some codes will clear after you hit 25 mph, while others will clear as soon as you move fast or long enough for the sensor to generate a positive reading.
How do I read my Polaris Ranger code?
Press and hold the MODE button the enter the Options Menu. “OPTIONS” will display on the screen for 3 seconds before showing the first menu item. 2. Select “Diagnostic Codes” from the Options Menu by pressing the MODE button.
Where is the speed sensor located on a Polaris Ranger?
rear gearcase
Located on the rear gearcase, it installs just like the original, no modifications required.
What is code 25 on Polaris Ranger?
Code 25 is Transmission Input: Invalid Gear. After you put it into park and shut off the engine, try rocking the RZR back and forth. You will hear it when it goes into park. Sometimes the parking pawl does not engage on level ground, and this will set this code.
How do you put a Polaris Ranger in diagnostic mode?
Registered
- Turn the key switch off and wait 10 seconds.
- Lock the parking brake.
- Place the transmission in neutral.
- Hold the mode/reverse override button and turn the key switch on. Release the switch as soon as the display is activated.
- Use the mode button to toggle through the diagnostic screens.
What does the wrench symbol mean on a Polaris Ranger?
Service Indicator. A flashing wrench symbol alerts the operator that the preset service interval has been reached. Your Polaris Dealer can provide scheduled maintenance.
Where is the speed sensor located?
Hello, the speed sensor for the speedometer is located on the transmission at the rear extension housing. The housing is the part that the driveshaft slip yoke (front part of driveshaft) would be position at. The sensor is attached with a bolt that needs to be removed, it has a two wire connector going to it.
How do you reset the check engine light on a Polaris Ranger?
Press the “Manual Override” button three times. This will cause the light to blink. Hold down the “Manual Override” button until the light stops blinking and turns off. This resets the service light.
Why will my Polaris Ranger not start?
Look at the air filter of your Polaris Ranger. It may have a clog in it, which chokes your engine and won’t allow it to run. Crank the engine again while looking at the electrode on the spark plug for a spark to see if it’s functioning properly. Replace the plug if it’s not getting a spark.
How do you reset the service light on a Polaris Ranger?
Use the following procedure to reset or change the service interval.
- Press and hold the MODE button to enter the settings menu.
- Press either toggle button to cycle to the “Service Hours” option. Press MODE to select.
- Press MODE to reset the existing value and exit or press either toggle button to change the value.
How to clear code 25 on PRC Polaris Ranger Club?
You can clear them by disconnecting the battery for 20 seconds, especially for code 25, but the others you’ll probably want to look into a little closer, for instance a short to ground can cause a fire under the right circumstances. There’s also a Diagnostic mode that will give status info and lets you set the clock.
How much does a Polaris Ranger XP cost?
RANGER XP 1000 Premium Starting at $17,599 US MSRP The standard for off-road utility with an unmatched combination of power, torque, comfort, convenience, and brute strength. Make no compromises with 82 HP, 2,500 LB towing, and 13″ clearance.
What makes a Polaris Ranger XP 1000 trail boss?
The RANGER XP 1000 Trail Boss includes all the features of the XP 1000 plus capability upgrades including 29″ tires, high clearance arched A-arms, and self-leveling suspension for more ground clearance. The performance of a RANGER XP 1000, with added features to dominate in the mud.
How is the Ranger XP 1000 Northstar rated?
Rated 1 out of 5 by EugeneSchmidtFarms from Constant Issues I bought the 2018 Ranger XP 1000 Northstar HVAC brand new last year and within the first couple months of using the machine I had random bolts coming out of the healiner and discovered the windshield leaked.